H8042CF-90bt AKTIVATECH Unmanaged Industrial DIN-Rail Switch 5-Port Gigabit IEEE 802.3bt PoE++
- 5-Port Gigabit IEEE 802.3bt PoE++ unmanaged Industrial DIN-Rail Switch
- with hardened Marvell IC and hardened PoE Controller
- 4x 90W Gigabit TX PSE + 1x Gigabit TX/SFP Combo + 1x 100/1000M SFP 52-56VDC
- Operating temp: -40°C to +75°C Wide Range Temperature
- DIN-Rail, Wall Mount
Specifications
|
IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3z 1000Base-X Gigabit Ethernet IEEE 802.3x Flow Control and Back Pressure IEEE 802.3af PoE IEEE 802.3at PoE+ IEEE 802.3bt PoE++ |
||
|
Switch Architecture |
Back-plane (Switching Fabric): 12Gbps |
|
|
Data Processing |
Store and Forward |
|
|
Flow Control |
IEEE 802.3x Flow Control and Back Pressure |
|
|
Jumbo Frame |
9KB |
|
|
MAC Address Table Size |
1K |
|
|
Packet Buffer Size |
1Mbits |
|
|
Network Connector |
5 x RJ-45 10/100/1000BaseT(X) auto negotiation, 4 x Gigabit 802.3at/af/bt PSE port 2 x SFP 100/1000M BaseX Auto MDI/MDI-X function, Full/Half duplex |
|
|
Network Cable |
UTP/STP Cat.5e or above Cable |
|
|
EIA/TIA-568 (100m) |
||
|
Protocol |
CSMA/CD |
|
|
LED |
PW1(Power 1) Green PW2(Power 2) Green ON: Power is detected OFF: Power is not detected ERR(Relay) Amber ON – Only one power (PW1 or PW2) is connected OFF – Both PW1 and PW2 are connected |
|
|
TX/RJ-45 port: P1~P4(PoE) Green ON: PD is detected on designated port OFF: No PD is detected LNK (Link/Active) Green ON: TX port is detected Flashing: TX data is transmitting/receiving SPD(Speed) Amber ON: 1000M speed is detected OFF: 10/100M speed is detected |
||
|
SFP Fiber Per port: F5/F6 Green ON: FX port is detected Flashing: FX data is transmitting/receiving |
||
DIP Switch |
DIP 1: F5: Port F5 SFP on (Default) T5: Port T5 TX on DIP 2: 1000M: SFP 1000M (Default) 100M: SFP 100M |
|
|
Reserve Polarity Protection |
Present |
|
|
Overload Current Protection |
Present |
|
|
Power Supply |
Redundant Dual DC 52V-56V Power Input |
|
|
Power Consumption |
5.76W@52 VDC full load, Without PoE |
|
|
Relay outputs with current carrying capacity of 1 A @24VDC, Relay in short circuit mode when 2 powers are connected. in open circuit mode when only one power supply is connected |
||
|
PoE power |
PoE power per port 90watts. Maximum total power 240Watts Supports IEEE802.3af/at/bt |
|
|
Removable Terminal Block |
Provide 2 Redundant power, Alarm relay contact ,6 Pin Wire range: 0.34mm^2 to 2.5mm^2 Solid wire (AWG):12-24/14-22 Stranded wire (AWG): 12-24/14-22 Torque:5lb-In/0.5Nm/0.56Nm Wire Strip length: 7-8mm |
|
|
Operating Temperature |
-40°C ~ 75°C fully tested. |
|
|
Operating Humidity |
5% to 95% (Non-condensing) |
|
|
Storage Temperature |
-40°C ~ 85°C |
|
|
MTBF (mean time between failure) |
502,179 hrs (Telcordia (Bellcore), GB) at 50°C |
|
|
Housing |
Rugged Metal, IP30 Protection |
|
|
Case Dimension (LxWxD) |
142 x 42.8 x 105 mm (L x W x D) |
|
|
Installation |
DIN Rail or Wall Mount options included |
|
|
Certifications |
||
|
Safety |
LVD (EN62368-1) |
|
|
EMC |
CE, FCC, EN 55032/35 |
|
|
EMI |
CISPR 32, FCC Part 15B Class A |
|
|
EMS |
IEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV IEC 61000-4-4 EFT: Power: 2KV; Signal: 2KV IEC 61000-4-5 Surge: Power: 2KV; Signal: 2KV |
|
|
Vibration |
EN 60068-2-6 |
|
|
Shock |
EN 60068-2-27 |
|
|
Free Fall |
EN 60068-2-32 |
|